AprintaPro

The sharp flexible needle makes loosen clogged residue easy and effortless. The all-metal quality build was specially chosen to withstand the heat of the nozzle and to be safe from melting plastic. Needle Method To remove a clog with the needle method an acupuncture or hypodermic needle is required. The size of the needle needs to be small enough to fit the nozzle. For a standard diameter of 0.4mm, the 0.3mm needle works perfect. Preheat the nozzle to the regular printing temperature for the material last in use. Be careful, the nozzle is hot and the all-metal construction of the needle conducts heat well. The goal is to break the blockage and clear the nozzle. Insert the needle from below and carefully move it around. Then remove the needle and insert filament manually from above and & push through. If the blockage is not yet clear repeat the steps. If this method does not work an alternative is the cold pull method.

Remove residue and clean your build plate with ease PrintaClean is a powerful solvent to remove dust, dirt and adhesive residue from the 3D printer build plate. Instruction Remove the build plate from the 3D printer. The build plate should be at room temperature and without damages. Spray a generous amount of PrintaClean on the build plate. Allow the solution around 30 seconds to disolve any residue Wipe off the solution with a kitchen towel.

PrintaFix is the best solution to eliminate first layer and adhesion problems. PrintaFix is the solution against warping. With its powerful formula, it keeps the 3D print fixated on the build plate until your model has finished. PrintaFix works with all standard materials and every model size, from small and delicate to big and tough. The application is finished in seconds. Just Shake & Spray an even film. A bottle of PrintaFix 500ml lasts on average for up to 750 3D prints. During the printing process PrintaFix bonds to the build plate and the print material to enable a secure connection. PrintaFix works great for PLA, PET-G, PLA or PET-G based filaments like WOOD filled or Carbon fiber filled filaments. After the print has finished, let it cool and lift to release. If you used much product or have a big surface on the build plate, use a scraper to loosen a corner and continue around the print How to use PrintaFix Preparation: Remove the build plate from the printer. The build plate should be at room temperature and without damage. Remove all dust and residue from previous prints from the build plate. Place it on a table and shake the PrintaFix bottle well for 5 seconds. Application: Hold the PrintaFix bottle 10cm (4”) away from the build plate. Use enough spray strokes to cover the entire build plate with a thin film of the solution. Overlap spray strokes to prevent uncovered areas that could affect the adhesion. Let it dry for 30 seconds. Print: Put the build plate back into the 3D printer and level it according to the settings of your model. Start the print process with recommended settings for the filament you use. Watch the first layers to make sure the adhesion is sufficient. Clean Up: When your print has finished remove it carefully with a spatula. Clean up of PrintaFix can be done with warm water, PrintaClean or an alcoholic solution. Window cleaner might also work – please check if they contain ethanol.

PrintaFix is the best solution to eliminate first layer and adhesion problems. PrintaFix is the solution against warping. With its powerful formula, it keeps the 3D print fixated on the build plate until your model has finished. PrintaFix works with all standard materials and every model size, from small and delicate to big and tough. The application is finished in seconds. Just Shake & Spray an even film. A bottle of PrintaFix 250ml lasts on average for up to 375 3D prints. During the printing process PrintaFix bonds to the build plate and the print material to enable a secure connection. PrintaFix works great for PLA, PET-G, PLA or PET-G based filaments like WOOD filled or Carbon fiber filled filaments. After the print has finished, let it cool and lift to release. If you used much product or have a big surface on the build plate, use a scraper to loosen a corner and continue around the print How to use PrintaFix Preparation: Remove the build plate from the printer. The build plate should be at room temperature and without damage. Remove all dust and residue from previous prints from the build plate. Place it on a table and shake the PrintaFix bottle well for 5 seconds. Application: Hold the PrintaFix bottle 10cm (4”) away from the build plate. Use enough spray strokes to cover the entire build plate with a thin film of the solution. Overlap spray strokes to prevent uncovered areas that could affect the adhesion. Let it dry for 30 seconds. Print: Put the build plate back into the 3D printer and level it according to the settings of your model. Start the print process with recommended settings for the filament you use. Watch the first layers to make sure the adhesion is sufficient. Clean Up: When your print has finished remove it carefully with a spatula. Clean up of PrintaFix can be done with warm water, PrintaClean or an alcoholic solution. Window cleaner might also work – please check if they contain ethanol.

PrintaFix Spray is the best solution to eliminate first layer and adhesion problems. PrintaFix Spray is the solution against warping. With its powerful formula, it keeps the 3D print fixated on the build plate until your model has finished. PrintaFix Spray works with all standard materials and every model size, from small and delicate to big and tough. The application is finished in seconds. Just Shake & Spray an even film. During the printing process PrintaFix bonds to the build plate and the print material to enable a secure connection. PrintaFix works great for PLA, PET-G, PLA or PET-G based filaments like WOOD filled or Carbon fiber filled filaments. After the print has finished, let it cool and lift to release. If you used much product or have a big surface on the build plate, use a scraper to loosen a corner and continue around the print How to use PrintaFix Spray Preparation: Remove the build plate from the printer. The build plate should be at room temperature and without damage. Remove all dust and residue from previous prints from the build plate. Place it on a table and shake the PrintaFix bottle well for 5 seconds. Application: Hold the PrintaFix bottle 10cm (4”) away from the build plate. Use enough to cover the entire build plate with a thin film of the solution. Overlap spray strokes to prevent uncovered areas that could affect the adhesion. Let it dry for 30 seconds. Print: Put the build plate back into the 3D printer and level it according to the settings of your model. Start the print process with recommended settings for the filament you use. Watch the first layers to make sure the adhesion is sufficient. Clean Up: When your print has finished remove it carefully with a spatula. Clean up of PrintaFix can be done with warm water, PrintaClean or an alcoholic solution. Window cleaner might also work – please check if they contain ethanol.

PrintaGlue is a universal superglue that has been chosen to work with a wide variety of 3D printing materials. It combines strength, quality, and durability for perfect results. It is always good to have Superglue in next to your 3D printer, as you never know when you will need a quick repair. PrintaGlue comes in easily portable 10g bottles, which last for many secure connections. Instructions The contact surfaces should be dry and free of contamination like oil or grease. Apply the adhesive sparingly to one surface. Press together immediately. Hold in place for 15 to 30seconds until bond sets. Let product rest for a while to give the glue time to fully harden. After 24h the bond has been fully set.

PrintaStick was engineered to solve the problem of warping! It is easy to apply adhesive for build plates that works with all common 3D printing materials and secures the 3D print until the print has finished. The formula is so powerful that for most prints the use of a raft or brim is not necessary saving time and material. The sponge applicator makes the usage easy, precise and effortless. During application and printing, PrintaStick does not release or produce any unpleasant smell, and after the print is finished, there is no visible trace of the solution on the 3D print. The formula is high temperature resistant and can therefore be used also for technical materials. Advantages Strong formula works for many materials precise to apply high temperature stable no unpleasant smell Instructions Prepare: Shake PrintaStick for a few seconds to mix the solution. Only apply on a cold residue free printbed. If necessary you can use PrintaClean to remove residue from the printbed. Apply: Apply PrintaStick by pressing the sponge applicator on the printbed to release some liquid. Then spread the liquid by moving the sponge in a circular pattern over the printbed. If the sponge hardens – rinse with clean water to soften. Print: Start the printing process with recommended temperature settings. The liquid will dry up during the heat up process of the printbed. Clean Up: When the printbed cools down the print will loosen from the build plate. Clean up with warm water.